To resolve questions, consult the latest revision of the actual specification. Milstd171 is the military standard that established the minimum requirements for finishing, and otherwise treating, metal and wood surfaces, and to serve as. Where a system in a previous edition of the standard has been deleted from this new revision, the system to be used as a substitute is noted in the tables. Where a system in a previous edition of mil std 171 has been deleted from the revision, the system to be used as a substitute is noted in the tables. This does not preclude the acceptance of a proven commercial finish selected by the manufacturer, suppliers, or contractor and concurred in by the procuring activity. Protective dtm acrylic primerfinish marine coatings. See mildtl16232g for the phosphate coating process requirements. The net result should be improved protection of military material from deterioration.
Anodizing specifications for commercial anodizing type i, ii, iii as. Stolit x is a readymixed, acrylicbased exterior or interior decorative and protective textured wall finish for use in stotherm ci systems and over prepared vertical above grade concrete, masonry, and stucco substrates. Finding that the milstd171 includes zinc phosphate is little information to anyone searching for the entire standard and all of its contents. Even if youve heard about, or have had direct experience with similar protective films, read on to find out what makes genuine toyota paint protection film a cut above competing products. Mil std 171 finishing of metal and wood surfaces this standard establishes and updates general finish codes and serves as a general guide to the selection of suitable materials, procedures, and system for cleaning, plating, painting and otherwise finishing of metal and wood surfaces. Finishes us26625 and us26d626 are only available up to 24h. A discussion started in 2004 but continuing through 2020. Does anyone know exactly what this protective finish is. Not measurement sensitive milstd171e 19 november 2001. Government and are not subject to protection in the u. Dchn llc one shorr court woonsocket, ri 02895 tel 4015975000. Note that specifications may be obtained at the following web. Fieldinstalled protection plates shall be labeled and installed in accordance with their listing exception.
Ncp coatings offers a full line of dynaspec qpld military specified coatings. Jun 07, 2011 finish system code numbers in the tables of mil std 171 are intended to remain stable, since those code numbers are commonly referenced on drawings, in contracts and in end items specifications. Military standard preparation for and installation of riviets. In this particular case, it is unnecessary to mention any preliminary steps such as cleaning, because astm b633, coatings of zinc of iron and steel zinc plating electrodeposited referenced in finish 1. Military standard preparation for and installation of. Gap limitations between joined sheets shall be in accordance with figures 1 and 6 and tables i, ii, iii and iv. Milstd171 new revision f released its the military. Combines the beauty of a hand rubbed finish with the toughness of polyurethane. Always wear lightweight surgical gloves to protect the skin and protective glasses to guard the eyes.
But, i guess the name of the game is to have a piece of paper that says it was done right, as opposed to actually doing it right. If circumstances make it desirable that parts of an assembly be primed. Hi, i have searched all over the web for what the specifications for finish 5. For convenience in referencing, all procedures, whether they merely clean a surface, deposit a film, or perform some other desirable function, are cataloged as finishes. As the mil std 171 standard pertains to aluminum parts and finishes provided by dchn mil std 171, 7. This ultrasmooth surface is less likely to harbour airborne contaminants or. Finishes contain chemicals that can be dangerous if used without proper safety precautions. Fda approves precision coatings micralox for use in repeatuse food processing. Finish specifications cross reference this chart is an approximate reference only. Additional information relative to protective finishes and their selection may be found in the appendix. Cross reference specifications dchn fine metal finishing. Welcome to, your online source for log home finishing products. Additional information relative to protective finishes and their selection may be found in milhdbk2 and mil std171. Milstd171 finishing of metal and wood surfaces document.
This does not preclude the acceptance of a proven commercial finish selected by the manufacturer, supplier or contractor and which is concurred in by the procuring activity. Sand wood or previous finishes in good condition to a smooth surface using 100120 grit sandpaper. Our primary mnphos military customers most often require coatings adhering to heavy manganese phosphate coating specification mildtl16232 type m, class 1, 2 or 3. Some parts might call out for surface improvement or in the case of stainless springs, may require passivation. Additional information relative to protective finishes and their selection msy be found in miledbk. Labeling is not required where the top of the protection plate is not more than 16 in. This specification is also referenced by mil std 171 finish numbers 5.
Mil std 171 is the military standard that established the minimum requirements for finishing, and otherwise treating, metal and wood surfaces, and to serve as a general guide to the selection of suitable finishing materials, procedures, and systems. Most springs, wire forms and stampings require plating finish for either a rust preventative or for cosmetic reasons. Additional information relative to protective finishes and their selection may be found in the appendix of this document. Strangely, the requirements that are not specific to any military application seem more comprehensive and specific than what i can find in mil std 171 3. Specifies and updates general finish codes and serves as a general guide. Manufacturing process standard for finishing of metal and wood. Finishes, coatings, and sealants, for the protection of aerospace weapons systems. May 14, 2015 consider mil std 171 a shopping list of finishes. The specifications listed are similar but not identical. The net result protection of military meteriel from,deterioration.
Ive been searching through the mil std 171 document and cant find a description of the process. Sto finish system for insulated concrete forms icf series 17. We deliver the great brands at the best prices with superior customer service. Information and documents presented here are works of the u. The following information will answer all of your questions about this superior vehicle finish protection. Coating for contents page the protection of structural steelwork this is an update of a dti publication first issued in 1982. This standard establishes and updates general finish codes and serves as a general guide to the selection of suitable materials. A common manual fly sprayer type applicator shall be used. Milstd7179 finishes, coatings, and sealants, for the. Ihc maintains process capability and certification requirements to numerous industry and manufacturer specifications, some of which are listed below. Some finishes emit hazardous fumes, so work outdoors or in a wellventilated area with a fan for circulation. Additional information relative to protective finishes and their selection msy be found in miledbk2 and the appendix of this document. This formulation is designed for long term protection over roof waterproofing systems.
Voted best value in a wipe on finish by fine woodworking magazine. Im quoting a part that calls out a protective finish 5. Aluma gold, milc5541 class 3, for protection against corrosion where low electrical resistance is required. Passivating is a chemical process on stainless steel that removes iron and loose particles that are formed during the manufacturing process. Milstd171 military specification for finishing of metal and wood surfaces. Can be applied to raw or stained wood, or over other minwax finishes. An integrated publishing website milstd171 finishing of metal and wood surfaces this standard establishes and updates general finish codes and serves as a general guide to the selection of suitable materials, procedures, and system for cleaning, plating, painting and otherwise finishing of metal and wood surfaces.
639 38 779 1257 264 1038 187 1449 1311 1259 1499 481 391 1440 782 42 738 105 1420 1483 1116 396 922 1379 1004 1280 391 58 928 864 679 846 1009 1253 367 852 1070